For my second attempt, I tried using less ink, but that made it necessary to squeegee over the silk several times before I pressed it onto the fabric to give it a last squeeg.
And that obviously pushed too much ink through the screen, so things filled in too much.
So: More ink, and just a single pass.
I bought a new Walkman the other week. I was quite impressed, and I remained impressed 
until I started to use them.
After wearing them for half an hour, the volume in the right speaker dropped down to almost nothing. It kinda varies, but it’s very very low.
I binged, and apparently this happens a lot. The recommended solution is to either get Sony to give you a new device, or to reset the device, so I did the latter.
And then it wouldn’t start up at all. It gave four “lower” beeps, and then one “high” beep, and then it switched itself off. I think that “high” beep is the “error beep”.
After fiddling around with it for a bit, I thought that perhaps it would help if I removed the songs from it, and I did. It would now boot and play stuff.
But the right speaker is still dead.
Geez, Sony.
Even though the screen wasn’t exposed well, I thought I could make an attempt to print something, just to see how that goes.
I put a backing board into the shirt to have firm to print onto. And then I put the shirt onto a frame to raise it from the floor, because I’m printing the screen from the wrong side, since I exposed the wrong side. Genius.
The ink is a lot firmer than I thought it would be. It just a glob of … stuff. I start wiping the squeegee all over the screen anyway.
Disaster. I pressed the paint through unevenly, and I think the backing board (in addition) wasn’t solid enough, so they kinda fade away.
Oh, well. Time to wash the screen and the squeegee. The paint is water soluble, fortunately, so that’s easy enough.
I think I’ll give this screen one more try, but squeegee things just once with a more even coat and see how that goes. But I think I have to make a new screen to get better results.
Despite not having the proper light, I’m attempting to do some screen printing. I have to practice, right?
So dissolve the sensitiser and pour it into the emulsion. It turns green!
Squeegee the emulsion onto the staple side of the screen in a dark-ish room, and let it dry for three hours in a very dark room.
Then put a transparent film positive onto the staple side and wait for an hour, since I have a 100W bulb, which is really too wimpy. People on the interwebs says that the emulsion turns either blue or a darker green when exposed, but it definitely remains green. It turns a slightly more dark shade of green, but it’s subtle.
Eurhm… when I’m printing the shirts, I’m supposed to flip the screen over, so won’t that make these prints mirror images?
YES! THEY WILL! D’oh. I’m supposed to either expose the other side of the screen or flip the transparencies over. People on the web seem to disagree on the preferred method. In any case, they way I did it is just wrong.
After an hour, I take the screen into the shower and blast it with cold water on both sides. As if by magic, lots of the unexposed areas are washed away, leaving a white silk. Seems to work well on the logo (which was furthest from the lamp), but the bits that were closest to the lamp seem over-exposed and won’t wash away.
In any case, since these are wrongly flipped, I can’t print them anyway… Or can I? Can I print using the wrong side of the screen? Worth a try before I wipe the screen, perhaps…
TO BE CONTINUED
While waiting for the screen to dry, I remembered that I had bought some iron-on transfers when I bought the printer, so I printed out a Gary Panter image on one of them.
I had bought transfers for white fabric (instead of black fabric) by accident, so I got out an old white t-shirt.
Peeel.
It actually kinda works.
But the colours aren’t very vibrant, and the black is kinda gray-ish…
After printing out the transfer, it seems like it starts fading… How about if I prep everything and then do the transfer immediately?
Nopes. Still kinda washed-out. And there’s a kinda of transparent residue where there’s “white”, which is kinda off-putting.
Oh, well. I didn’t expect these to look as good as they do, so…
TO BE CONTINUED